1967 Cadillac EldoradoGERALD´S CADILLACS - NEWS

Repairing the Treadle Vac Master Cylinder and Brake Booster of my 58 Eldorado

In June I bled the brakes of the 58 Seville because it needed some fresh fluid, and the fluid level was a little low in the reservoir of the Bendix Treadle Vac master cylinder.
Now as I wanted to drive it out of the garage, I found a puddle of brake fluid under the car.
So I went on to search where it was coming from.
I suspected a leaking wheel cylinder, but could not find any traces of fluid coming from the wheels. After some more searching, I eventually found out that fluid was dripping out under the brake booster along the push rod. When I checked the fluid level it was only half full.

So I knew that the Treadle Vac would need a full rebuild…
I ordered a rebuild kit at Cadillac Parts LTD. They offer a kit to rebuild everything from the booster to the master cylinder. As I found out, the gasket for the reservoir did not fit from their set and some other correct smaller rubber parts are also not included in the set. So remove everything carefully from your unit as you might have to reuse some parts for your rebuild. I contacted them about the wrong parts and they immediately sent me the correct parts by mail. Great customer services - I would order from them anytime again!

As I had never done a full rebuild I asked my Cadillac friend Lucky for help - knowing that he can repair almost everything, and that he had done this job during the full restoration of his awesome 58 Biarritz before.

He was so kind to offer his assistance and invited me to his fantastic work shop where he is restoring his cars.

So I carefully removed the whole unit from my car and visited Lucky´s workshop.

With his skills he managed to rebuild the whole unit within a couple of hours. As it turned out a bad O-ring caused fluid to leak into the booster.
Due to all the brake fluid the finish of the Bendix unit suffered a lot, and so I decided to strip everything on the outside down to bare metal to repaint it.
So I took everything apart once again to make sure to do it perfectly.
I ordered some great spray cans from Eastwood to get the perfect look to match its appearance to when it was new.
Originally the master cylinder was not painted at all - but left in bare cast metal. Of course it started to collect surface rust very quickly - even on new cars back in 1958.
The booster originally was painted in semi gloss black.

Eastwood has a product called "Brake Gray" which I used to emulate this look. It comes extremely close to bare metal, but of course the paint protects the metal from rust. This paint is also resistant against brake fluid. I first primered the master cylinder with self etching primer two times before two coats of brake gray were applied.

For the brake booster I ordered Eastwoods Chassis Black extreme primer and satin black paint - painting turned out really fine! See pictures below

To make bleeding brakes easier and a one person job I also ordered a set of speed bleeder screws. (SB3824-SS)


edge
The unit still in the car - before removal
edge
Removal has started
edge
The unit out of the car - before rebuilding it.
edge
Out of the car
edge
In Lucky´s workshop with the rebuild kit I got from the USA
edge
My friend Lucky at work
edge
Lucky´s fantastic work shop
edge
The Bendix master cylinder fully disassembled


Everything disassembled

edge
This O-ring was leaking and caused the problem.

edge
The new o-ring in place.

boosterrepair-SM_MG_8489
The vacuum cylinder
boosterrepair-SM_MG_8492
edge
As you can see the paint suffered from the brake fluid - a repaint was necessary after the rebuild.

boosterrepair-SMIMG_3635
I started to wire brush the paint off - took it apart once again after this picture.

boosterrepair-SMIMG_3655
The master cylinder in primer.

edge
After painting it with "Brake Gray" - great stuff.

edge
The master cylinder with paint
edge
The booster in bare metal before primer. I used Eastwood Extrem Chassis Black primer and paint.

edge
In primer

edge
Speed Bleeder screws
edge
Speed Bleeder screws and bag
edge
The new Speed Bleeder screw in place
edge
The reassembled unit back in the car.

Comments